Event ID - 41008

Event Id41008
SourceMicrosoft-Windows-RasRoutingProtocols-IGMPv2
DescriptionIGMP was unable to create a semaphore. The data is the error code.
Event Information According to Microsoft :

Cause :

This event is logged when IGMP was unable to create a semaphore.

Resolution :

Configure or reinstall the IGMP interface, check memory status, or restart Routing and Remote Access service

Possible resolutions:
  • Delete and reinstall the IGMP interface. For more information, see the "Delete IGMP interface" and "Install IGMP interface" sections.
  • Check the configuration settings on the interface. For more information, see the "Configure IGMP" section.
  • This computer might be low on memory. For more information, see the "Check memory usage on the server" section.
  • Stop and restart the Routing and Remote Access service. For more information, see the "Restart the remote access service" section.
  • Restart the computer.
To perform these procedures, you must have membership in Administrators , or you must have been delegated the appropriate authority.

Delete the IGMP interface

To delete the IGMP interface:
  1. Open Routing and Remote Access. Click Start , click Run , type rrasmgmt.msc , and then press ENTER.
  2. In the console tree, expand IPv4 , and then click IGMP .
  3. In the details pane, right-click the interface you want to configure, and then click Delete .
  4. Click Yes in the confirmation dialog box.
Install the IGMP interface

To install the IGMP interface:
  1. Open Routing and Remote Access. Click Start , click Run , type rrasmgmt.msc , and then press ENTER.
  2. In the console tree, expand IPv4 , right-click IGMP , and then click New Interface .
  3. Select an interface, and then click OK .
  4. Configure the IGMP settings, and then click OK .
Configure IGMP

To configure IGMP:
  1. Open Routing and Remote Access. Click Start , click Run , type rrasmgmt.msc , and then press ENTER.
  2. In the console tree, expand IPv4 , and then click IGMP .
  3. In the details pane, right-click the interface you want to configure, and then click Properties .
  4. Check the settings on the General and Router tabs.
Check memory usage on the server

To check memory usage on the remote access server:
  1. On the remote access server, click Start , click Run , type taskmgr , and then click OK .
  2. In the Windows Task Manager dialog box, click the Performance tab.
  3. Under Physical Memory , check the remote access server's memory usage.
  4. If necessary, free up available memory by ending nonessential applications or processes.
Restart the remote access service

To restart the remote access service:service:
  1. Open Routing and Remote Access. Click Start , click Run , type rrasmgmt.msc , and then press ENTER.
  2. By default, the local computer is listed as a server. To add another server, in the console tree, right-click Server Status , and then click Add Server . In the Add Server dialog box, click the appropriate option, and then click OK .
  3. In the console tree, right-click the server you want to restart, click All Tasks , and then click Restart .
Verify :

You can verify multicast routing configuration with the mrinfo command. You can use the configuration information to aid in the troubleshooting of multicast forwarding and routing problems.

The mrinfo command queries a specified multicast router with an Internet Group Management Protocol (IGMP) message. The response to the query contains a version number, the list of interfaces and the neighbors on each interface, metrics, Time to Live (TTL) thresholds, and flags. The syntax of the mrinfo command is:

mrinfo [- n ] [ -i address ] [ - r retry_count ] [ - t timeout_count ] multicast_router
  • The - n option displays IP addresses in numeric format.
  • The - i option specifies the IP address of the interface from which you want to send the mrinfo query. By default, the interface from which to send the mrinfo query is determined by the IP routing table.
  • The - r option specifies the neighbor query retry limit. The default value is 3.
  • The - t option specifies how long, in seconds, mrinfo waits for a neighbor query reply. The default value is 4.
The following is an example of the mrinfo command:

C:\>mrinfo 10.1.0.1

10.1.0.1(test1.microsoft.com) [version 18.55,mtrace,snmp]:

10.1.0.1 -> 0.0.0.0 (local) [1/0/querier/leaf]

10.2.0.1 -> 10.2.0.2 (test2.microsoft.com) [1/0]

10.2.0.1 -> 10.2.0.3 (test3.microsoft.com) [1/0]

10.3.0.1 -> 0.0.0.0 (local) [1/0/querier/leaf]

In the preceding example, mrinfo is run against the multicast router at 10.1.0.1. The first line shows the multicast router configuration: version number (for servers running Routing and Remote Access, the version number reflects the build number of the operating system) and flags (mtrace and snmp supported).

Each additional line displays the interfaces on the multicast router and the neighbors on each interface. Interfaces 10.1.0.1 and 10.3.0.1 have no neighbors. Interface 10.2.0.1 has two neighbors, 10.2.0.2 and 10.2.0.3. For each line, mrinfo displays the interface and neighbor, the domain name for the neighbor, the multicast routing metric, the TTL threshold, and flags indicating its role on the network, such as the IGMP querier of the network (querier) or whether it has no neighbors (leaf).
Reference LinksEvent ID 41008 from Microsoft-Windows-RasRoutingProtocols-IGMPv2

Catch threats immediately

We work side-by-side with you to rapidly detect cyberthreats
and thwart attacks before they cause damage.

See what we caught

Did this information help you to resolve the problem?

Yes: My problem was resolved.
No: The information was not helpful / Partially helpful.